XLINE AUTOCAD SERIES

Similarly, we can use the above types of construction line in multiple ways.

Specify the side (direction) to create an offset, as shown in the below image:.

Select the Offset option on the command line.

Type O on the command line or command prompt and press Enter.

It is used to create an offset of a specified line object. These lines will be drawn with a fixed specified vertex point.

Similarly, continue specifying the angle end point to draw multiple lines.

It will be the point to fix the position of the construction line. You can specify these two points according to the requirements.

Specify angle start point, as shown in the below image:.

Select Bisect option on the command line.

Type B on the command line or command prompt and press Enter.

It creates all the lines from the specified angle vertex point or bisect point. Here, we have specified the reference point, as shown in the below image: Bisect Construction Line We can specify any reference point according to the requirements.

Specify the through point and place the line on the desired position with the help of cursor.

Type R or Reference on the command line after step 1 and step 2 as given above.

Specify the reference point for the construction line. The construction line will be drawn, as shown in the below image: Specify the first and second point on the viewport, as shown in the below image: The line of infinite length will be drawn, as shown in the below image: Remember: The angle is measured in counter-clockwise direction in AutoCAD.

Specify the angle of XLine (Construction line).

Type A on the command line or command prompt and press Enter.

The steps to create an angle construction line are listed below: We can draw multiple vertical lines by clicking (specifying the through point) as many times on the viewport. The vertical construction line of infinite length will be drawn, as shown in the below image:

Type V on the command line or command prompt and press Enter.

The steps to create a vertical construction line are listed below: We can draw multiple horizontal lines by clicking (specifying the through point) as many times on the viewport.

The horizontal construction line of infinite length will be drawn, as shown in the below image:

Specify a through point on the viewport.

Select Hor option displayed on the command line, as shown in the below image:

Type H on the command line or command prompt and press Enter.

Type XL on the command line and press Enter.

Click on the Construction Line icon, as shown in the below image:.

The steps to create a horizontal construction line are listed below:

The construction line can be drawn in different ways, which are listed below: Note: The icon of the Construction Line will be visible under the 'Draw' section on the ribbon panel. We can further trim the boundaries according to the requirements. It is used as a reference to create other objects, as shown in the below image: Offset : Create a straight line in parallel with the existing straight line.The construction line is used to create a line of infinite length.– Offset : Create a straight line in parallel with the existing straight line. – Angle end point: choose a point of the second side of angle – Angle start point: choose a point of the first side of angle – Specify angle vertex point: choose vertex of angle The first point belongs to angle center, the second point and the third point belong to 2 sides of angle. Specify through point: choose a point belong to the straight lineīisect: create a straight line across bisector of an angle (through 3 points), at this choice AutoCAD requests you to enter 03 points.Enter angle of xline (0) or : enter oblique angle.3.2.10 Drawing XLINE Xline is infinite line, commonly used in. After this choice, AutoCAD requests you to enter. Veja grtis o arquivo AutoCAD-2021-From-Zero-to-Hero-by-Akbar -Ali-Putra -Zico-Pratama. Ang: Create straight line with a bevel angle.

After this choice, you just enter (or catch a point) a point that the straight line passes.

XLINE AUTOCAD SERIES

through point: choose another point if you want to draw a series of straight lines across the first point.through point: choose the second point of straight line.a point or : choose a point to start drawing (or choose H,V,A,B,O).

In drawing projection surface, you can use this command to find drawing point together with Trim, Scale command… you can create the sides of projection. This command is usually used to draw extension lines, horizontal or vertical lines. XLINE (Construction line) is usually used as the command to draw extension line in CAD. XLINE command in CAD to draw a straight line or a series of intersect straight lines.

Xline autocad